Modely
Celkem 204 produktů
1/32 RAF FE.2b - Fabric Seat Belts - 2 sets Wingnut Wings. Textile seat belts designed for aircraft RAF FE.2b by Wingnut Wings. Belts are made from real microfibre and in combination with included photo etched buckles they look highly realistic. This product is available in 1/32 scale. HGW models SEATBELTS in 1:32 scale - this set is designed for Wingnut Wings kits textile sheeting, metallic buckles it is possible to make seat belts fully functional - un/buckle, un/fasten them made by special micro-textile foil set contains seat belts for 2 single-seater aeroplanes textile parts are prepared to using filters - it leads to darkening shades - and these are also waterproofedand resistant to normal nonaggresive modeller preparations photo-etched parts were developed in cooperation with Eduard company INSTRUCTIONS This set contains printed and photoetched parts. Choose appropriate shade of belt and trim on dotted line using very sharp knife. Trim to required length according to the type of seatbelt. Using fingers munch into little ball. Flatten out and thread through photoetched parts. Glue using white glue, do not use chemical glue that eches plastic. When applying, look at photos of cockpit of individual machines. After glued and shaped, paint with matt varnish.
1/32 RAF FE.2b - Fabric Seat Belts - 2 sets Wingnut Wings. Textile seat belts designed for aircraft RAF FE.2b by Wingnut Wings. Belts are made from real microfibre and in combination with included photo etched buckles they look highly realistic. This product is available in 1/32 scale. HGW models SEATBELTS in 1:32 scale - this set is designed for Wingnut Wings kits textile sheeting, metallic buckles it is possible to make seat belts fully functional - un/buckle, un/fasten them made by special micro-textile foil set contains seat belts for 2 single-seater aeroplanes textile parts are prepared to using filters - it leads to darkening shades - and these are also waterproofedand resistant to normal nonaggresive modeller preparations photo-etched parts were developed in cooperation with Eduard company INSTRUCTIONS This set contains printed and photoetched parts. Choose appropriate shade of belt and trim on dotted line using very sharp knife. Trim to required length according to the type of seatbelt. Using fingers munch into little ball. Flatten out and thread through photoetched parts. Glue using white glue, do not use chemical glue that eches plastic. When applying, look at photos of cockpit of individual machines. After glued and shaped, paint with matt varnish.
1/32 Light wood - Transparent - Decals Wood Grain - transparent no grid sheet: A5. A5 sheet This type is transparent, so it is possible, through base colour, to regulate final shade of the decal. Wooden structure is equal to 1/32 scale. INSTRUCTIONS Pasted/fixed/glued, puttied and polished model paint by base white (it is suitable to polish also this coloured layer before applying wooden decals). The decals are transparent, so it is necessary to apply base colour. It is possibe to mark off single panels by using different shades of base colour (white, of white, yellow). Then cut required shape of panel (with 2 mm overlap) and apply as same as ordinary decal (use Mr. Mark Setter, Mr. Mark Softer). After these processes cut protruded wooden decal with very sharp knife. By this technique it is possible to create very believable imitation of the wooden surface without skill in using of oil paints.
1/32 Dark wood - Transparent - Decals Wood Grain - transparent no grid sheet: A5. A5 sheet This type is transparent, so it is possible, through base colour, to regulate final shade of the decal. Wooden structure is equal to 1/32 scale. INSTRUCTIONS Pasted/fixed/glued, puttied and polished model paint by base white (it is suitable to polish also this coloured layer before applying wooden decals). The decals are transparent, so it is necessary to apply base colour. It is possibe to mark off single panels by using different shades of base colour (white, of white, yellow). Then cut required shape of panel (with 2 mm overlap) and apply as same as ordinary decal (use Mr. Mark Setter, Mr. Mark Softer). After these processes cut protruded wooden decal with very sharp knife. By this technique it is possible to create very believable imitation of the wooden surface without skill in using of oil paints.
1/32 Dark wood - Transparent - Decals Wood Grain - transparent no grid sheet: A5. A5 sheet This type is transparent, so it is possible, through base colour, to regulate final shade of the decal. Wooden structure is equal to 1/32 scale. INSTRUCTIONS Pasted/fixed/glued, puttied and polished model paint by base white (it is suitable to polish also this coloured layer before applying wooden decals). The decals are transparent, so it is necessary to apply base colour. It is possibe to mark off single panels by using different shades of base colour (white, of white, yellow). Then cut required shape of panel (with 2 mm overlap) and apply as same as ordinary decal (use Mr. Mark Setter, Mr. Mark Softer). After these processes cut protruded wooden decal with very sharp knife. By this technique it is possible to create very believable imitation of the wooden surface without skill in using of oil paints.
1/32 Light wood - Transparent - Decals Wood Grain - transparent no grid sheet: A5. A5 sheet This type is transparent, so it is possible, through base colour, to regulate final shade of the decal. Wooden structure is equal to 1/32 scale. INSTRUCTIONS Pasted/fixed/glued, puttied and polished model paint by base white (it is suitable to polish also this coloured layer before applying wooden decals). The decals are transparent, so it is necessary to apply base colour. It is possibe to mark off single panels by using different shades of base colour (white, of white, yellow). Then cut required shape of panel (with 2 mm overlap) and apply as same as ordinary decal (use Mr. Mark Setter, Mr. Mark Softer). After these processes cut protruded wooden decal with very sharp knife. By this technique it is possible to create very believable imitation of the wooden surface without skill in using of oil paints.
1/48 Messerschmitt Bf 109G-6 - Microplastic Seat Belts - pre-cut (laser). Seat belts, suitable for plastic scale aircrafts, are made from micro-plastic foil. In combination with attached photo etched buckles this accesorry looks highly realistic. These are available in 1/48 scale and for more comfortable work they are pre-cut. contains highly detailed micro-plastic and photo-etched partsbelts are fully functional - modeler can leave them un/fastenedmade from printed micro-plastic material which credibly simulates textilebelts are prepared for using filters and other agents (they are waterproof and resistant to common nonaggresive modeling preparationsphoto-etched parts are developed in cooperation with Hauler company
1/48 Messerschmitt Bf 109G-6 - Microplastic Seat Belts - pre-cut (laser). Seat belts, suitable for plastic scale aircrafts, are made from micro-plastic foil. In combination with attached photo etched buckles this accesorry looks highly realistic. These are available in 1/48 scale and for more comfortable work they are pre-cut. contains highly detailed micro-plastic and photo-etched partsbelts are fully functional - modeler can leave them un/fastenedmade from printed micro-plastic material which credibly simulates textilebelts are prepared for using filters and other agents (they are waterproof and resistant to common nonaggresive modeling preparationsphoto-etched parts are developed in cooperation with Hauler company
1/32 Fokker E.I - Fabric Seat Belts - pre-cut (laser) Wingnut Wings. Accessory designed for vintage model aircraft by Wingnut Wings. Seat belts from HGW Models are laser-cut so it is easy-to-use product. Set contains micro fabric belts and photo etched buckles suitable for large scale planes in 1/32 scale. contains micro-fabric and photo-etched highly detailed parts designed for great Fokker E.IV by Wingnut Wings belts are fully functional - modeler can leave them un/fastened made from printed micro-fabric material which behaves like a piece of rag textile parts are prepared for using filters and other agents (they are waterproof and resistant to common nonaggresive modeling preparations photo-etched parts are developed in cooperation with Eduard company
1/32 Fokker E.IV - Fabric Seat Belts - pre-cut (laser) Wingnut Wings. Accessory designed for vintage model aircraft by Wingnut Wings. Seat belts from HGW Models are laser-cut so it is easy-to-use product. Set contains micro fabric belts and photo etched buckles suitable for large scale planes in 1/32 scale. contains micro-fabric and photo-etched highly detailed parts designed for great Fokker E.IV by Wingnut Wings belts are fully functional - modeler can leave them un/fastened made from printed micro-fabric material which behaves like a piece of rag textile parts are prepared for using filters and other agents (they are waterproof and resistant to common nonaggresive modeling preparations photo-etched parts are developed in cooperation with Eduard company
1/32 Fokker E.IV - Fabric Seat Belts - pre-cut (laser) Wingnut Wings. Accessory designed for vintage model aircraft by Wingnut Wings. Seat belts from HGW Models are laser-cut so it is easy-to-use product. Set contains micro fabric belts and photo etched buckles suitable for large scale planes in 1/32 scale. contains micro-fabric and photo-etched highly detailed parts designed for great Fokker E.IV by Wingnut Wings belts are fully functional - modeler can leave them un/fastened made from printed micro-fabric material which behaves like a piece of rag textile parts are prepared for using filters and other agents (they are waterproof and resistant to common nonaggresive modeling preparations photo-etched parts are developed in cooperation with Eduard company
1/32 Fokker E.I - Fabric Seat Belts - pre-cut (laser) Wingnut Wings. Accessory designed for vintage model aircraft by Wingnut Wings. Seat belts from HGW Models are laser-cut so it is easy-to-use product. Set contains micro fabric belts and photo etched buckles suitable for large scale planes in 1/32 scale. contains micro-fabric and photo-etched highly detailed parts designed for great Fokker E.IV by Wingnut Wings belts are fully functional - modeler can leave them un/fastened made from printed micro-fabric material which behaves like a piece of rag textile parts are prepared for using filters and other agents (they are waterproof and resistant to common nonaggresive modeling preparations photo-etched parts are developed in cooperation with Eduard company
1/32 Albatros D.V / D.Va - Fabric Seat Belts - pre-cut (laser) Wingnut Wings. Textile seat belts designed for aircraft Albatros D.V / D.Va by Wingnut Wings. Belts are made from real microfibre and in combination with included photo etched buckles they look highly realistic. This product is available in 1/32 scale. HGW models SEATBELTS in 1:32 scale - this set is designed for Wingnut Wings kits textile sheeting, metallic buckles it is possible to make seat belts fully functional - un/buckle, un/fasten them made by special micro-textile foil set contains seat belts for 2 single-seater aeroplanes textile parts are prepared to using filters - it leads to darkening shades - and these are also waterproofedand resistant to normal nonaggresive modeller preparations photo-etched parts were developed in cooperation with Eduard company INSTRUCTIONS This set contains printed and photoetched parts. Choose appropriate shade of belt and trim on dotted line using very sharp knife. Trim to required length according to the type of seatbelt. Using fingers munch into little ball. Flatten out and thread through photoetched parts. Glue using white glue, do not use chemical glue that eches plastic. When applying, look at photos of cockpit of individual machines. After glued and shaped, paint with matt varnish.
1/32 Halberstadt CI.II - Fabric Seat Belts - pre-cut (laser). Accessory designed for vintage model aircraft by Wingnut Wings. Seat belts from HGW Models are laser-cut so it is easy-to-use product. Set contains micro fabric belts and photo etched buckles suitable for large scale planes in 1/32 scale.
1/32 Halberstadt CI.II - Fabric Seat Belts - pre-cut (laser). Accessory designed for vintage model aircraft by Wingnut Wings. Seat belts from HGW Models are laser-cut so it is easy-to-use product. Set contains micro fabric belts and photo etched buckles suitable for large scale planes in 1/32 scale.
1/32 Gotha G.I / UWD - Fabric Seat Belts - pre-cut (laser) Wingnut Wings. Limited edition exclusive for Art Scale Textile seat belts designed for aircraft Albatros D.V / D.Va by Wingnut Wings. Belts are made from real microfibre and in combination with included photo etched buckles they look highly realistic. This product is available in 1/32 scale. HGW models SEATBELTS in 1:32 scale - this set is designed for Wingnut Wings kits textile sheeting, metallic buckles it is possible to make seat belts fully functional - un/buckle, un/fasten them made by special micro-textile foil set contains seat belts for 2 single-seater aeroplanes textile parts are prepared to using filters - it leads to darkening shades - and these are also waterproofedand resistant to normal nonaggresive modeller preparations photo-etched parts were developed in cooperation with Eduard company INSTRUCTIONS This set contains printed and photoetched parts. Choose appropriate shade of belt and trim on dotted line using very sharp knife. Trim to required length according to the type of seatbelt. Using fingers munch into little ball. Flatten out and thread through photoetched parts. Glue using white glue, do not use chemical glue that eches plastic. When applying, look at photos of cockpit of individual machines. After glued and shaped, paint with matt varnish.
1/32 Gotha G.I / UWD - Fabric Seat Belts - pre-cut (laser) Wingnut Wings. Limited edition exclusive for Art Scale Textile seat belts designed for aircraft Albatros D.V / D.Va by Wingnut Wings. Belts are made from real microfibre and in combination with included photo etched buckles they look highly realistic. This product is available in 1/32 scale. HGW models SEATBELTS in 1:32 scale - this set is designed for Wingnut Wings kits textile sheeting, metallic buckles it is possible to make seat belts fully functional - un/buckle, un/fasten them made by special micro-textile foil set contains seat belts for 2 single-seater aeroplanes textile parts are prepared to using filters - it leads to darkening shades - and these are also waterproofedand resistant to normal nonaggresive modeller preparations photo-etched parts were developed in cooperation with Eduard company INSTRUCTIONS This set contains printed and photoetched parts. Choose appropriate shade of belt and trim on dotted line using very sharp knife. Trim to required length according to the type of seatbelt. Using fingers munch into little ball. Flatten out and thread through photoetched parts. Glue using white glue, do not use chemical glue that eches plastic. When applying, look at photos of cockpit of individual machines. After glued and shaped, paint with matt varnish.
1/32 Albatros D.V / D.Va - Fabric Seat Belts - pre-cut (laser) Wingnut Wings. Textile seat belts designed for aircraft Albatros D.V / D.Va by Wingnut Wings. Belts are made from real microfibre and in combination with included photo etched buckles they look highly realistic. This product is available in 1/32 scale. HGW models SEATBELTS in 1:32 scale - this set is designed for Wingnut Wings kits textile sheeting, metallic buckles it is possible to make seat belts fully functional - un/buckle, un/fasten them made by special micro-textile foil set contains seat belts for 2 single-seater aeroplanes textile parts are prepared to using filters - it leads to darkening shades - and these are also waterproofedand resistant to normal nonaggresive modeller preparations photo-etched parts were developed in cooperation with Eduard company INSTRUCTIONS This set contains printed and photoetched parts. Choose appropriate shade of belt and trim on dotted line using very sharp knife. Trim to required length according to the type of seatbelt. Using fingers munch into little ball. Flatten out and thread through photoetched parts. Glue using white glue, do not use chemical glue that eches plastic. When applying, look at photos of cockpit of individual machines. After glued and shaped, paint with matt varnish.
Plastikový model letadla 1/72 Folland Gnat FR.1 Finnish Recce Fighter. The Folland Gnat fighter aircraft was operated mainly by the military of Finland and India. Two of the Finnish airframes were delivered in the Gnat FR.1 reconnaissance variety equipped with a set of cameras in the nose section. They were coded GN-112 and GN-113 and flew recon and mapping sorties. They, however, retained their cannon armament and ability to fly in the fighter role, too. The model comes on three grey styrene sprues and two made of clear plastic. The decal sheet covers both Finnish recon machines. unusual and interesting variety of the Gnat the decals offer a full set of stencils wide variety of wing armament masks and detail sets also available: M72004, CMK 7332,7333, Q72236, Q72237
Plastikový model letadla 1/72 Folland Gnat FR.1 Finnish Recce Fighter. The Folland Gnat fighter aircraft was operated mainly by the military of Finland and India. Two of the Finnish airframes were delivered in the Gnat FR.1 reconnaissance variety equipped with a set of cameras in the nose section. They were coded GN-112 and GN-113 and flew recon and mapping sorties. They, however, retained their cannon armament and ability to fly in the fighter role, too. The model comes on three grey styrene sprues and two made of clear plastic. The decal sheet covers both Finnish recon machines. unusual and interesting variety of the Gnat the decals offer a full set of stencils wide variety of wing armament masks and detail sets also available: M72004, CMK 7332,7333, Q72236, Q72237
1/32 Focke Wulf Fw 190A-8 - Fabric Seat Belts - pre-cut (laser). The set contains complete belts for two aircrafts. Accessory designed for your plastic model Fw190A-8. Seat belts from HGW Models are laser-cut so it is easy-to-use product. Set contains micro fabric belts and photo etched buckles suitable for large scale planes in 1/32 scale. ACCESSORY FEATURES contains micro-fabric and photo-etched highly detailed partsbelts are fully functional - modeler can leave them un/fastenedmade from printed micro-fabric material which behaves like a piece of ragtextile parts are prepared for using filters and other agents (they are waterproof and resistant to common nonaggresive modeling preparations INSTRUCTIONS Take the precut textile part out of the sheet.Remove the carrier paper.Bunch the belts up and knead them between the fingers.Thread the belts through the photo etched buckles – use superglue.Put them into the seat.Spray with glossy varnish.Spray with matt varnish.Impregnate the seat belts with very diluted oil colour (mix of black and brown) > texture highlight.
1/32 Focke Wulf Fw 190A-8 - Fabric Seat Belts - pre-cut (laser). The set contains complete belts for two aircrafts. Accessory designed for your plastic model Fw190A-8. Seat belts from HGW Models are laser-cut so it is easy-to-use product. Set contains micro fabric belts and photo etched buckles suitable for large scale planes in 1/32 scale. ACCESSORY FEATURES contains micro-fabric and photo-etched highly detailed partsbelts are fully functional - modeler can leave them un/fastenedmade from printed micro-fabric material which behaves like a piece of ragtextile parts are prepared for using filters and other agents (they are waterproof and resistant to common nonaggresive modeling preparations INSTRUCTIONS Take the precut textile part out of the sheet.Remove the carrier paper.Bunch the belts up and knead them between the fingers.Thread the belts through the photo etched buckles – use superglue.Put them into the seat.Spray with glossy varnish.Spray with matt varnish.Impregnate the seat belts with very diluted oil colour (mix of black and brown) > texture highlight.